www.micropowerdirect.com micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com w ww.m i cro p ower di rect.com www.micropowerdirect.com micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com electrical speci cations speci cations typical @ +25?, 230 vac input voltage & rated output current, unless otherwise noted. speci cations subject to change without notice. compact, led, 150w constant current ac/dc power supply key features: 150w output power ul 8750 approved constant current output active pfc 90 - 305 vac input ip65 / ip67 rated meets en 55015, en 61547 dimming function >50 khour life expectancy lightning surge protection over volt/temp protection LDC-150 series input parameter conditions min. typ. max. units input voltage range 90 305 vac 127 431 vdc input frequency 47 63 hz inrush current, see note 1 230 vac 75 a pk input current 115 vac 2.10 a 230 vac 0.90 264 vac 0.80 power factor correction 0.98 @ 115 vac 0.95 @ 230 vac 0.93 @ 264 vac total harmonic distortion (thd) see note 2 10 % turn on delay, see note 3 115 vac 1.5 s 230 vac 0.5 leakage current 277 vac 0.75 ma output parameter conditions min. typ. max. units output current accuracy 5.0 % line regulation v in = min to max 1.0 % ripple & noise (20 mhz) see note 4 2.0 v p-p output ripple current 5.0 % hold-up time 115 vac 12.0 ms over temperature protection 10%, autorecovery 85 c short circuit protection continuous (autorecovery) overload protection autorecovery 95 107 % iout general parameter conditions min. typ. max. units isolation voltage, 60s input to output 3,750 vac input to fg 2,000 output to fg 500 insulation resistance input to output 100 m / 500 vdc / 25 c / 70% rh input to fg output to fg emi characteristics parameter standard emi en 55015; en 6100-3-2, -3; fcc part 18; cns 14115; gb 17743 ems en 61547; en 61000-4-2,-3, -4, -5, -6, -8, -11; gb 17625.1 surge 10 kv (l/n - fg), 5 kv (l-n)/1.2 x 50 s environmental parameter conditions min. typ. max. units operating temperature range ambient -40 +25 +70 c storage temperature range -40 +85 c cooling free air convection (see derating curve on page 2) humidity rh, non-condensing 95 % physical case size see mechanical diagrams (page 4) weight 33.1 oz (950g) reliability speci cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25c, gnd benign 220 khours life expectancy see note 5 50 khours safety standards ul 8750 approved, meets en 61347, gb 19510.1, gb 19510.14 vibration 5 - 500 hz, 1g , 1 oct/min, 2 cycles, period for 75 min. each along x, y, & z axis
292 page street ste d stoughton, ma 02072 ? tel: (781) 344-8226 ? fax: (781) 344-8481 ? e-mail: sales@micropowerdirect.com www.micropowerdirect.com model number output output power (w) ef ciency (%, typ) current voltage range (vdc) ovp level (vdc) max (ma) adj. range (ma) LDC-150-2450 x 2,450 1,650 - 2,450 32 - 58 62 - 80 142 91 LDC-150-3150 x 3,150 2,000 - 3,150 32 - 49 54 - 73 154 91 LDC-150-3500 x 3,500 2,200 - 3,500 27 - 42 49 - 65 147 91 LDC-150-4550 x 4,550 2,750 - 4,550 25 - 35 41 - 55 159 91 model selection guide notes: 1. inrush current is given for a cold start at 25?. 2. total harmonic distortion (thd) is speci ed with an input of 230 vac/50 hz at full load. 3. turn on delay is speci ed at full load. 4. ripple & noise is measured at 20 mhz. connection to the unit is made with a 0.1 ? ceramic capacitor and a 22 ? electrolytic capacitor connected in parallel. 5. life expectancy is calculated at 230 vac, full load and a case temp of +70?. 6. recovery from an over voltage fault is automatic. derating curve: temperature ef ciency vs load: LDC-150-4550 derating curve: input voltage pfc vs load: LDC-150-4550 model ingress protection dimming function LDC-150-xxxx a ip65 adjust by internal, variable resistor LDC-150-xxxx b ip67 adjust by external resistor, dc voltage level or pwm signal package type
micropower direct ? 292 page street ste d stoughton, ma 02072 ? tel: (781) 344-8226 ? fax: (781) 344-8481 ? e-mail: sales@micropowerdirect.com www.micropowerdirect.com dimming mode: b model functional block diagram with the LDC-150 ? model, the output current level can be adjusted (dimmed) by three different methods; resistive, analog or digital. adjustments are made using the +dim and -dim inputs. resistive: connect a 0.1 to 10 k resistor between the dim+ (blue) and dim- (white) wires input frequency 10 k 20 k 30 k 40 k 50 k 60 k 70 k 80 k 90 k 100 k open percentage of rated current 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 95~105% analog: apply 1 vdc to 10 vdc level between the dim+ (blue) and dim- (white) wires adjust voltage 1 vdc 2 vdc 3 vdc 4 vdc 5 vdc 6 vdc 7 vdc 8 vdc 9 vdc 10 vdc open percentage of rated current 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 95~105% digital: apply a pwm signal (100 hz - 3 khz) between the dim+ (blue) and dim- (white) wires duty cycle 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% open percentage of rated current 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 95~105% notes: 1 . the -dim (white) and -led (black) wires should not be connected. 2. the dimming function will not turn the lighting xture totally off. for more info on how to do this, please contact the factory
micropower direct we power your success - for less! 292 page street ste d stoughton, ma 02072 ? tel: (781) 344-8226 ? fax: (781) 344-8481 ? e-mail: sales@micropowerdirect.com www.micropowerdirect.com mechanical dimensions: a model mechanical dimensions: b model (dimming function) color function green/yellow field ground brown ac-line blue ac-neutral wire connections: input color function black -led red +led wire connections: output color function green/yellow field ground brown ac-line blue ac-neutral wire connections: input color function white -dim blue +dim black -led red +led wire connections: output
|
